Panasonic CS-RZ25TKR Скачать руководство пользователя страница 126

Страница: 126 / 196

126

17.4.11 H28 (Outdoor Pipe Temperature Sensor Abnormality)

Malfunction Decision Conditions



During startup and operation of cooling and heating, the temperatures detected by the outdoor pipe temperature

sensor are used to determine sensor errors.

Malfunction Caused



Faulty

connector

connection.



Faulty

sensor.



Faulty

PCB.

Troubleshooting

Is the measured resistance of the outdoor heat exchanger
temperature sensor matches the value specified in its
characteristic chart?

Is the connector connection normal?

When abnormality indication starts again.

For safety reason and to prevent
component breakdown, always switch
off the power before remove and
connect the component.

YES

Check the outdoor heat exchanger temperature sensor:

Plug out connector from the outdoor unit PCB.
Measure the resistance of the outdoor heat exchanger
temperature sensor.

Check the connector connection:

Turn off the power.
Check the connector connection.

Connector poor contact.
Correct the connection.

Defect in outdoor unit PCB.
Replace the outdoor unit PCB.

Defect in outdoor heat exchanger
temperature sensor.
Replace the outdoor heat exchanger
temperature sensor.

-10

Temperature (°C)

sta

nce

)

Sensor (Thermistor)

Characteristics

Outdoor Air Sensor
Outdoor Heat Exchanger
Sensor

Содержание CS-RZ25TKR





































































































































































































Результаты поиска

Содержание CS-RZ25TKR

Отзывы:

Бренды по названию

Популярные бренды

Panasonic CS-RZ25TKR, Руководство по обслуживанию

Результаты поиска

Содержание CS-RZ25TKR

Отзывы:

Бренды по названию

Популярные бренды