Panasonic CS-RZ25TKR Скачать руководство пользователя страница 138

Страница: 138 / 196

138

17.4.22 F93 (Compressor Rotation Failure)

Malfunction Decision Conditions



A compressor rotation failure is detected by checking the compressor running condition through the position

detection circuit.

Malfunction Caused



Compressor terminal disconnect.



Faulty Outdoor PCB.



Faulty

compressor.

Troubleshooting

When F93 indication happens.

Check the U, V and W connector connection:
- Turn OFF the power.
- Check the U, V and W connector connection at

outdoor PCB and compressor terminal.

From the disconnected harnesses U, V and W,
correct them to the inverter checker. Turn ON the
power and operate the system. Check the inverter
checker 6 LEDs blinking condition.

Disconnect the harnesses U, V and W from the
compressor terminal.

Is the blinking of the 6 LEDs in same
sequence/condition.

Is the connector connection normal?

For safety reason and to prevent
component breakdown, always
switch off the power before remove
and connect the component.

Correct the connection.

Connector poor contact.

YES

Replace outdoor unit PCB.

IPM defective.

Replace compressor.

Содержание CS-RZ25TKR





































































































































































































Результаты поиска

Содержание CS-RZ25TKR

Отзывы:

Бренды по названию

Популярные бренды

Panasonic CS-RZ25TKR, Руководство по обслуживанию

Результаты поиска

Содержание CS-RZ25TKR

Отзывы:

Бренды по названию

Популярные бренды