Panasonic CS-RZ25TKR Скачать руководство пользователя страница 123

Страница: 123 / 196

123

17.4.8 H24 (Indoor Pipe Temperature Sensor 2 Abnormality)

Malfunction Decision Conditions



During startup and operation of cooling and heating, the temperatures detected by the indoor heat exchanger

temperature sensor 2 are used to determine sensor errors.

Malfunction Caused



Faulty

connector

connection.



Faulty

sensor.



Faulty

PCB.

Troubleshooting

When abnormality indication starts again.

For safety reason and to prevent component
breakdown, always switch off the power
before remove and connect the component.

Connector poor contact.
Correct the connection.

Defect in outdoor unit PCB.
Replace the outdoor unit PCB.

Defect in outdoor intake air temperature sensor.
Replace the outdoor intake air temperature
sensor.

YES

Check the connector connection:

Plug out connector from the indoor unit PCB.

Is the connector connection normal?

Measure the resistance of the indoor pipe temperature
sensor 2.

Check the outdoor air temperature sensor:

Is the measured resistance of the outdoor intake air
temperature sensor matches the value specified in its
characteristic chart?

Plug out connector from the outdoor unit PCB.
Measure the resistance of the outdoor intake air
temperature sensor.

-10

Temperature (°C)

Resistan

)

Sensor (Thermistor)

Characteristics

Pipe temp. Sensor
Intake Air Temp. Sensor

Содержание CS-RZ25TKR





































































































































































































Результаты поиска

Содержание CS-RZ25TKR

Отзывы:

Бренды по названию

Популярные бренды

Panasonic CS-RZ25TKR, Руководство по обслуживанию

Результаты поиска

Содержание CS-RZ25TKR

Отзывы:

Бренды по названию

Популярные бренды