Panasonic CS-RZ25TKR Скачать руководство пользователя страница 124

Страница: 124 / 196

124

17.4.9 H25 (nanoe-G Air Purifying System Abnormal)

Malfunction Decision Conditions



During standby of cooling and heating operation, nanoe-G breakdown occurs and air conditioner stops operation.

Malfunction Caused



Faulty indoor main PCB.



Faulty indoor nanoe-G power module.

Troubleshooting

When abnormality indication starts again

●

Turn off the power, and reconnect CN-CLN connector

●

Turn on the power, and measure again the DC voltage
between CN-CLN channel 4 & 2

Is the voltage measured at 5Vdc?

●

Defect in indoor unit nanoe-G power module

●

Replace the indoor unit nanoe-G power module

●

Defect in indoor unit main PCB

●

Replace the indoor unit main PCB

Check the indoor unit main PCB CN-CLN terminal 4 & 2 DC
voltage:

●

Turn off the power

●

Disconnect the CN-CLN connector

●

Turn on the power, measure the DC voltage between
CN-CLN terminal 4 & 2

Is the DC voltage measured at 5Vdc?

●

Defect in indoor main PCB

●

Replace the indoor unit main PCB

YES

For safety reason and to prevent component
breakdown, always switch off the power
before remove and connect the component.

nanoe-G power

module

WIRE HOLDER

TRO

HV(-)

HV(+)

GND

Содержание CS-RZ25TKR





































































































































































































Результаты поиска

Содержание CS-RZ25TKR

Отзывы:

Бренды по названию

Популярные бренды

Panasonic CS-RZ25TKR, Руководство по обслуживанию

Результаты поиска

Содержание CS-RZ25TKR

Отзывы:

Бренды по названию

Популярные бренды