Panasonic CS-RZ25TKR Скачать руководство пользователя страница 131

Страница: 131 / 196

131

17.4.16 H97 (Outdoor Fan Motor – DC Motor Mechanism Locked)

17.4.16.1 CU-Z20/25/35/42/50/60/71TKR

Malfunction Decision Conditions



The rotation speed detected by the Hall IC during fan motor operation is used to determine abnormal fan motor.

Malfunction Caused



Operation stops due to short circuit inside the fan motor winding.



Operation stops due to breaking of wire inside the fan motor.



Operation stops due to breaking of fan motor lead wires.



Operation stops due to Hall IC malfunction.



Operation error due to faulty outdoor unit PCB.

Troubleshooting

YES

When abnormality indication starts again

Turn off power supply and disconnect
CN-MTR2 connector. Connect inverter
checker to CN-MTR2 then turn power on.

Replace fan motor

For safety reason and to prevent
component breakdown, always switch
off the power before remove and
connect the component.

Caution

Does fan rotate smoothly?

Is all 6 LED on and off periodically?

Main outdoor PCB transistor faulty

Replace outdoor PCB

Turn off power supply and rotate fan by
hand

Check the output of fan motor from outdoor
PCB

Fan motor faulty

Replace fan motor

YES

Check fan motor winding U-V, V-W, U-W.
Is value consistent in all readings?

YES

Is the fan motor rotation start and stop
intermittently during initial running?

YES

Содержание CS-RZ25TKR





































































































































































































Результаты поиска

Содержание CS-RZ25TKR

Отзывы:

Бренды по названию

Популярные бренды

Panasonic CS-RZ25TKR, Руководство по обслуживанию

Результаты поиска

Содержание CS-RZ25TKR

Отзывы:

Бренды по названию

Популярные бренды