Panasonic CS-RZ25TKR Скачать руководство пользователя страница 141

Страница: 141 / 196

141

17.4.25 F97 (Compress Overheating)

Malfunction Decision Conditions



During operation of cooling and heating, when compressor tank temperature data (103°C) is detected by the

compressor tank temperature sensor.

Malfunction Caused



Faulty compressor tank temperature sensor



2/3 way valve closed



Refrigerant

shortage

(refrigerant leakage)



Faulty outdoor unit PCB



Faulty

compressor

Troubleshooting

When F97 indication happens.

For safety reason and to prevent component
breakdown, always switch off the power
before remove and connect the component.

Replace the compressor tank
temperature sensor.

Repair the pipe flare or union nuts.
Reclaim and recharge refrigerant.

Open the 2/3 way valve.

Procedure complete.

Check the compressor tank temperature
sensor.

Does it conform to the sensor
characteristic chart?

Check if expansion valve or strainer
clogged (ice formed).

Reclaim and recharge for a specified
amount of refrigerant.

2/3 way valve closed?

Check for gas leakage.

Oil oozing out from the 2/3 way valve?

Refrigerant cycle abnormality error again?

YES

Replace expansion valve and/or strainer.
Reclaim and recharge refrigerant.

YES

Replace outdoor unit PCB.
Replace outdoor unit compressor.

YES

Содержание CS-RZ25TKR





































































































































































































Результаты поиска

Содержание CS-RZ25TKR

Отзывы:

Бренды по названию

Популярные бренды

Panasonic CS-RZ25TKR, Руководство по обслуживанию

Результаты поиска

Содержание CS-RZ25TKR

Отзывы:

Бренды по названию

Популярные бренды