Panasonic CS-RZ25TKR Скачать руководство пользователя страница 128

Страница: 128 / 196

128

17.4.13 H33 (Unspecified Voltage between Indoor and Outdoor)

Malfunction Decision Conditions



The supply power is detected for its requirement by the indoor/outdoor transmission.

Malfunction Caused



Wrong models interconnected.



Wrong indoor unit and outdoor unit PCBs used.



Indoor unit or outdoor unit PCB defective.

Troubleshooting

When abnormality indication starts again.

For safety reason and to prevent
component breakdown, always switch
off the power before remove and
connect the component.

Check indoor and outdoor units model number.

Check indoor and outdoor PCB part number and compare if
they matched the part list.

Is the indoor and outdoor unit model number matched?

●

Match the compatible model (follow specification).

YES

●

Replace the indoor and outdoor unit PCB.

Change for the specified indoor or outdoor unit PCB.

Содержание CS-RZ25TKR





































































































































































































Результаты поиска

Содержание CS-RZ25TKR

Отзывы:

Бренды по названию

Популярные бренды

Panasonic CS-RZ25TKR, Руководство по обслуживанию

Результаты поиска

Содержание CS-RZ25TKR

Отзывы:

Бренды по названию

Популярные бренды