Panasonic AJ-CX4000G страница 3 Скачать руководство пользователя

Страница: 3 / 221

Read this first!

– 3 –

indicates safety information.

FCC NOTICE (USA)

Supplier’s Declaration of Conformity

Trade Name:

Panasonic

Model Number:

AJ-CX4000G

Responsible Party: Panasonic Corporation of North America

Two Riverfront Plaza Newark NJ07102

Support contact:

1-800-524-1448

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference

received, including interference that may cause undesired operation.

FCC Warning:

To assure continued FCC emission limit compliance, follow the attached installation instructions and the

user must use only shielded interface cables when connecting to host computer or peripheral devices. Also,

any unauthorized changes or modifications to this equipment could void the user’s authority to operate this

device.

FCC Caution:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant

to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may cause harmful interference

to radio communications. However, there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is encouraged to try to correct the interference by

one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help. The user may find the booklet

“Something About Interference” available from FCC local regional offices helpful.

NOTIFICATION (Canada)

CAN ICES-3(B)/NMB-3(B)

AEEE Yönetmeliğine Uygundur.

AEEE Complies with Directive of Turkey.

Manufactured by: Panasonic Corporation, Osaka, Japan

Importer’s name and address of pursuant to EU rules:

Panasonic Marketing Europe GmbH

Panasonic Testing Centre

Winsbergring 15, 22525 Hamburg, Germany

Содержание AJ-CX4000G






























































































































































































































Результаты поиска

Содержание AJ-CX4000G

Отзывы:

Похожие инструкции для AJ-CX4000G

Бренды по названию

Популярные бренды

Panasonic AJ-CX4000G, Руководство по эксплуатации

Результаты поиска

Содержание AJ-CX4000G

Отзывы:

Похожие инструкции для AJ-CX4000G

Бренды по названию

Популярные бренды