Panasonic AJ-CX4000G страница 127 Скачать руководство пользователя | Manualshive

Страница: 127 / 221

background image

– 127 –

Chapter 5 Shooting — Flash band compensation (FBC) function

Flash band compensation (FBC) function

The camera is equipped with a function for compensating and reducing band-like interference (called “flash band”) that occurs due to the MOS pickup
device when shooting in environments where flash strobe light such as that from still cameras is present.

Change over time

Shot image

(FBC OFF)

Flash firing

Flash band

Setting the flash band compensation function

Assign the flash band compensation function to the USER buttons.
By pressing the USER buttons that are assigned with the flash band compensation function, the function turns on, and flash strobe from a still camera,
etc. can be detected and compensated.
For details, refer to “Assigning function to the USER buttons” (page 129).
When the flash band compensation function is enabled, [FBC] is displayed on the STATUS screen.

INTRVL

HD

FLUO.

14.6V

FBC

RELAY

HDR

CAC

@

@

NOTE

t

When the flash strobe lights, the following phenomena may occur. These are due to the flash band compensation function and are not malfunctions.
-  Moving subjects look as if they have stopped suddenly.
-  The resolution when the flash strobe light drops.
-  Horizontal lines appear in the video when the flash strobe lights.
-  Flash bands may appear only in images shot at the time the flash is fired.

Using the flash band compensation function

The flash band compensation function is activated when there are large changes in brightness at the bottom of the screen regardless of whether there
is flash strobe light. The flash band compensation function may be activated depending on the shooting environment such as where a bright window has
zoomed in and then out. So, we recommend use of this function in shooting environments where flash strobe lighting is anticipated.
Even if flash strobe lighting occurs, sufficient flash band compensation function effect may not be obtained in some shooting environments.

Flash band compensation function operation conditions

f

The flash band compensation function can be used under the conditions that electronic shutter and digital super gain functions are all not operating.

f

Even if the flash band compensation function is enabled, the flash band compensation function is temporarily disabled if the camera is changed to a
mode where the flash band compensation function cannot be used.
When using the function again, return to a mode that can use the flash band compensation function. Flash band compensation function will be
automatically enabled.
The flash band compensation function is disabled once the power is turned off.

«
...
125
126
127
128
129
...
»

Содержание AJ-CX4000G






























































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для AJ-CX4000G

Бренд: DXG Страницы: 1

Бренд: Samsung Страницы: 128

Бренд: RCA Страницы: 28

Бренд: Hitachi Страницы: 86

Бренд: Hitachi Страницы: 61

Бренд: Hitachi Страницы: 71

VM-873LA - Camcorder

Бренд: Hitachi Страницы: 64

Бренд: Hitachi Страницы: 105

Бренд: Hitachi Страницы: 143

VM-865LA - Camcorder

Бренд: Hitachi Страницы: 64

VM-7500LA - Camcorder

Бренд: Hitachi Страницы: 59

VM-975LA - Camcorder

Бренд: Hitachi Страницы: 64

Бренд: Hitachi Страницы: 65

Бренд: Hitachi Страницы: 64

Бренд: Hitachi Страницы: 28

Бренд: Hitachi Страницы: 66

Бренд: Hitachi Страницы: 156

Бренд: Hitachi Страницы: 40

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды