Panasonic AJ-CX4000G страница 27 Скачать руководство пользователя | Manualshive

Страница: 27 / 221

background image

– 27 –

Chapter 2 Description of Parts — Shooting and recording/playback functions section

Shooting and recording/playback functions section (Recording unit)

1

15

14

11
12

3

13

6 7 8 9

2

2

4

10

5

1

<REC> button

Recording is started by pressing the <REC> button. Recording is stopped by pressing this button again.
Performs the same operation as the <VTR> button of the lens to be attached.

2

Card access lamp 1/card access lamp 2/card access lamp 3

Indicates the access status of recording and playback of the memory card.

3

Card slot 1

This is a card slot only for expressP2 card.

4

<USB DEVICE> terminal

In the USB device mode, the camera can be connected to the computer by the USB type C cable to transfer data.In this case, recording playback
operations and camera shooting are not possible.

5

Card slot 2/card slot 3

These are card slots for microP2 card and SD card.

6 <REV (

%

)> button

It will perform fast-reverse playback when this is pressed during playback.
It will playback from the start of the clip when this is pressed while paused.

7 <STOP (

(

)> button

Press this button to stop playback.

8

<FWD (

)

)> button

It will perform fast playback when this is pressed during playback.
It will play back from the start of the next clip when this is pressed while paused during a playback.

9 <PLAY/PAUSE (

=

/

&

)> button

Plays back a clip.
Playback is paused when this is pressed during the playback.

10

<SDI OUT 2 CHARACTER> switch

Controls the superimposing of characters into the video output from the <SDI OUT2> terminal.
Controls the superimposing of characters into the video output from the <HDMI> terminal when the [VIDEO OUT/LCD/VF] menu

→

[HDMI OUT]

→

[SIGNAL SEL]

→

[SDI OUT2] is set.

<ON>:

Superimposes the character.

<OFF>:

Does not superimpose the character.

11

<USB2.0 HOST> terminal

Can connect via wireless LAN when the wireless module (optional) compatible to camera is mounted.

12

<HDMI> terminal

This is the output terminal for videos.
Output signal can be switched with the [VIDEO OUT/LCD/VF] menu

→

[HDMI OUT]

→

[SIGNAL SEL].

[SDI OUT1(2160p)]:

Follows the setting of the output signal from the <SDI OUT1> terminal.

[SDI OUT2]:

Follows the setting of the output signal from the <SDI OUT2> terminal.

Setting for superimposing of characters can be switched in the [VIDEO OUT/LCD/VF] menu

→

[HDMI OUT]

→

[SIGNAL SEL].

13

<LAN> terminal

Connects the 1000BASE-T/100BASE-TX/10BASE-T LAN cable.
Use Category 7 LAN cable.

«
...
25
26
27
28
29
...
»

Содержание AJ-CX4000G






























































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для AJ-CX4000G

Бренд: MYDLINK Страницы: 2

Бренд: D-Link Страницы: 4

Бренд: Myria Страницы: 20

DV PROLINE AG-DVC20

Бренд: Panasonic Страницы: 3

DVCPRO HD P2 AG-HVX200

Бренд: Panasonic Страницы: 16

DVCPRO AJ-D410AP

Бренд: Panasonic Страницы: 46

DVCPRO HD AJ-HD1800E

Бренд: Panasonic Страницы: 142

DVD e.cam VDR VDR-D210

Бренд: Panasonic Страницы: 156

Digital Palmcorder PV-GS55

Бренд: Panasonic Страницы: 176

Digital Palmcorder PV-GS70

Бренд: Panasonic Страницы: 226

Бренд: Panasonic Страницы: 4

Бренд: Panasonic Страницы: 6

Бренд: Panasonic Страницы: 3

DVD Palmcorder Camcorder VDR-D310

Бренд: Panasonic Страницы: 12

Бренд: Panasonic Страницы: 30

Бренд: Panasonic Страницы: 95

DVD Palmcorder VDR-D220

Бренд: Panasonic Страницы: 124

Бренд: Panasonic Страницы: 168

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды