Panametrics CGA 351 Скачать руководство пользователя страница 90

Страница: 90 / 119

Chapter 5.

CGA 351 User’s Manual

Replacing the Fuse

If the main power fuse is defective, install a new fuse by completing the following steps:

Note:

For information regarding component locations and/or wiring connections in an optional enclosure, see

Appendix C.

Disconnect the main power to the CGA 351.

WARNING!

Failure to cut the main power at the external

disconnect device before proceeding will result in

serious personal injury.

Remove the cover beneath the digital display panel on the electronics enclosure.

Locate the fuse holder (see Figure 6 on page 14) on the lower right side of the terminal board. Remove the old

fuse.

Install a new fuse of the same type and rating. See Chapter 6,

Specifications, for the correct fuse to use.

Install the cover on the electronics enclosure, and reapply power to the analyzer.

The CGA 351 may now be placed back into service.

Replacing the Digital Panel Meter

If the digital panel meter is defective, remove the defective meter by completing the following steps:

Note:

For information regarding component locations and/or wiring connections in an optional enclosure, see

Appendix C.

Disconnect the main power to the CGA 351.

WARNING!

Failure to cut the main power at the external

disconnect device before proceeding will result in

serious personal injury.

Remove the four sets of mounting hardware and remove the electronics enclosure from its mounting surface.

Remove the eight screws on the rear of the enclosure and lift the mounting plate off the enclosure.

Make a sketch of all wiring connections to the rear of the digital panel meter, and then disconnect all the wiring.

Remove the two mounting brackets and push the panel meter out through the front of the enclosure. Remove the

controller and option cards from Slots 1 and 2, respectively.

Install the new meter by completing the following steps:

Install the original controller and option cards into Slots 1 and 2, respectively, of the new meter.

Insert the new meter through the opening in the front of the electronics enclosure and secure it in place with the

two brackets.

Reconnect all of the wires to the connectors on the rear of the new digital panel meter.

Place the mounting plate over the rear of the electronics enclosure and secure it with the eight screws previously

removed.

Mount the electronics enclosure back onto the wall/panel and secure it with the four sets of hardware previously

removed.

Reconnect the main power to the analyzer.

Refer to Chapter 3,

Operation, and Chapter 4, Setup and Calibration, to reprogram the new digital panel meter.

The CGA 351 is now ready to be placed back into service.

Replacing the Controller Card

To replace a defective controller card, complete the following steps:

Содержание CGA 351
























































































































Результаты поиска

Содержание CGA 351

Отзывы:

Panametrics CGA 351, Руководство пользователя, Страница: 90 / 119

Результаты поиска

Содержание CGA 351

Отзывы: