manualshive.com logo in svg

PALAZZANI RAGNO TSJ 30.1, Руководство по эксплуатации и безопасности

Поделиться
Скачать
PALAZZANI RAGNO TSJ 30.1 Скачать руководство пользователя страница 45

Tel. 0039 030 6857073 - Fax 0039 030657079           [email protected] - www.palazzani.it

Pag.  36

OM2016_US

 !

WARNING

Ensure that all protective devices are connected and in good function. Ne-
ver modify or bypass any safety devices of the machine.

 !

WARNING

Both during during the maintenance and operational phases it is recom-
mended to pay attention to the temperature of engines that can be more 
than 50 ° C in normal operation.

 !

WARNING

The machine can not be used by unprofessional staff, or not previously 
trained to the use, informed about the remaining risks of the machine and 
trained on safety and correct operating methods.

DANGER

Do not use the machine in aerial work when the wind speed exceeds 12.5 
m / s (45 km / h)

2.10.   OPERATOR’S PROTECTIVE EQUIPMENT

For operator safety reasons, PPE (or other available equipment) are compulsory for the 
use of the machine.
The manufacturer requires the customer to use the machine with PPE complying with 
Directive 89/686 / CEE as amended, relating to personal protective equipment properly 
CE marked.
The operator must comply with Directive 89/656 / CEE defi ning the methods of use of 
personal protective equipment at work.
Since all contexts where the machine work are not known, it must be underlined that the 
above mentioned PPE refer only to the use of the machine: the employer must prescribe 
any additional PPE in accordance with the needs of the environment in which the ma-
chine operates.

Depending on the country , it is owner’s responsibility to comply with different local 
safety regulations.

Содержание RAGNO TSJ 30.1




































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды