Owon SDS-E Series Скачать руководство пользователя страница 86 | Manualshive

Страница: 86 / 106

background image

6.Communication with PC

81

6.

Communication with PC

Digital storage oscilloscope  support communications with a PC through USB, LAN or
COM port. You can use the Oscilloscope  communication software to store, analyze,
display the data and remote control.
Here is how to connect with PC. First, install the Oscilloscope communication software on
the supplied CD. Then there are several ways of connection to choose from.

Using USB Port

(1)

Connection:

Use a USB data cable to connect the

USB Device port

in the right panel

of the Oscilloscope to the USB port of a PC.

(2)

Install the driver:

Run the Oscilloscope communication software on PC, press F1 to

open the help document. Follow the steps of title "

I. Device connection

" in the

document to install the driver.

(3)

Port setting of the software:

Run the Oscilloscope software; click

"Communications"  in the menu bar, choose  "Ports-Settings",  in the setting dialog,
choose  "Connect using"  as  "USB". After connect successfully, the connection
information in the bottom right corner of the software will turn green.

Figure 6-1 Connect with PC through USB port

«
...
84
85
86
87
88
...
»

Содержание SDS-E Series











































































































Отзывы:

Нет отзывов

Похожие инструкции для SDS-E Series

Relion 670 series

Бренд: ABB Страницы: 66

Бренд: Sagola Страницы: 8

Бренд: ADVANCED HOME CARE Страницы: 16

Infield Rascal Pro

Бренд: ABI Attachments Страницы: 8

Бренд: Abicor Binzel Страницы: 84

Бренд: ABI Attachments Страницы: 5

Бренд: abem Страницы: 47

Бренд: Abely Страницы: 5

Бренд: ACCU-CHECK Страницы: 104

Бренд: XM Fitness Страницы: 10

Бренд: Olsen Страницы: 4

Dominator Series

Бренд: Falcon Страницы: 31

Бренд: Fakir Страницы: 22

Бренд: Hach Страницы: 66

Бренд: Hach Страницы: 14

Бренд: Hach Страницы: 144

QuikChem 8500 2 Series

Бренд: Hach Страницы: 80

Бренд: Hach Страницы: 178

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды