Owon SDS-E Series Скачать руководство пользователя страница 65

Страница: 65 / 106

5.Advanced User Guidebook

Figure 5-54

Wave Storage

To use wave record function, do as follows:
(1)

Press

Save

button.

(2)

Press

button, turn the

knob to choose

Record

(3)

Press

button. In the Mode menu, press

button to choose

Record

(4)

Press

button. In the Frame Set menu, press

button and turn the

knob to set

End frame; press

button and turn the

knob to select the interval between

recorded frames.

(5)

Press

button, choose whether to refresh the wave when recording.

(6)

Press

button to start recording.

(7)

Press

button. In the Mode menu, press

button to enter the

Playback

mode. Set

the frame range and

Playmode

.Then, press

button to play.

(8)

To save the wave recorded, press

button. In the Mode menu, press

button to

choose

Storage

, then set the range of frames to store, press

button to save.

(9)

To load the waveform from the internal memory, press

Load

, and then enter playback

mode to analyze the wave.

When storage medium is External, Wave Record contains two modes: OFF, Record.

Содержание SDS-E Series











































































































Результаты поиска

Содержание SDS-E Series

Отзывы:

Похожие инструкции для SDS-E Series

Бренды по названию

Популярные бренды

Owon SDS-E Series, Руководство пользователя

Результаты поиска

Содержание SDS-E Series

Отзывы:

Похожие инструкции для SDS-E Series

Бренды по названию

Популярные бренды