Owon SDS-E Series Скачать руководство пользователя страница 67

Страница: 67 / 106

5.Advanced User Guidebook

Figure 5-56: Frame setting (External Storage)

To use wave record to external, do as follows:
1.

Press

Save

button.

Press

button, turn the

knob to choose

Record

Press

button. In the Mode menu, press

button to choose

Record

. Press

choose

External

as the storage medium.

Press

button. In the Frame Set menu, press

button and turn the

knob to set

End frame; press

button and turn the

knob to select the interval between

recorded frames. Press

to wave record to external infinitely if necessary, and end

frame will display “-”.

Press

button, choose whether to refresh the wave when recording.

Press

button to start recording.

Connect external device to the computer, and wave_record_0.bin is the recorded file.
Open the software, and do as follows to play back the waveform.

Choose Communications



Auto Player.

Transform recording waveform from machine.

Add the well transformed files.

Set play mode and time delay.

Click the green button on the left corner to begin playing back the waveform.

Содержание SDS-E Series











































































































Результаты поиска

Содержание SDS-E Series

Отзывы:

Похожие инструкции для SDS-E Series

Бренды по названию

Популярные бренды

Owon SDS-E Series, Руководство пользователя

Результаты поиска

Содержание SDS-E Series

Отзывы:

Похожие инструкции для SDS-E Series

Бренды по названию

Популярные бренды