Owon SDS-E Series Скачать руководство пользователя страница 75

Страница: 75 / 106

5.Advanced User Guidebook

Press the

button again, the type items will display at the left of screen, and turn the

knob to choose

Freq

Press the

button, the frequency added completes, finish setting of CH1.

Press the

button and choose

CH2

as the source.

Press the

button, the type items will display at the left of screen, and turn the

knob to choose

Mean

10.

Press the

button, the Mean added completes.

11.

Press the

button, the type items will display at the left of screen, and turn the

knob to choose

PK-PK

12.

Press the

button, the PK-PK added completes, finish setting of CH2.

The measured value will be displayed at the bottom left of the screen automatically
(see

Figure 5-68

Figure 5-68 Automatic measurement

The automatic measurement of voltage parameters

The oscilloscopes provide automatic voltage measurements including Mean, PK-PK,
RMS, Max, Min, Vtop, Vbase, Vamp, OverShoot, PreShoot, Cycle RMS, and Cursor
RMS.

Figure 5-69

below shows a pulse with some of the voltage measurement points.

Содержание SDS-E Series











































































































Результаты поиска

Содержание SDS-E Series

Отзывы:

Похожие инструкции для SDS-E Series

Бренды по названию

Популярные бренды

Owon SDS-E Series, Руководство пользователя

Результаты поиска

Содержание SDS-E Series

Отзывы:

Похожие инструкции для SDS-E Series

Бренды по названию

Популярные бренды