Owon SDS-E Series Скачать руководство пользователя страница 69

Страница: 69 / 106

5.Advanced User Guidebook

menu.

Figure 5-59

Display Menu

The description of

Display

Menu

is shown as the follows:

●

Adjust

Press the

Utility

button and turn the

knob to select the

Adjust

to go to the following

menu.

Figure 5-60 Adjust Menu

The description of

Adjust

Menu

is shown as the follows:

Do Self Cal (Self-Calibration)

The self-calibration procedure can improve the accuracy of the oscilloscope under the
ambient temperature to the greatest extent. If the change of the ambient temperature is
up to or exceeds 5

℃

, the self-calibration procedure should be executed to obtain the

highest level of accuracy.

Before executing the self-calibration procedure, disconnect the probe or wire and the
input connector. Press the

Utility

button. Then, press the

button and the function

menu will display at the left of the screen, turn the

knob to choose "

Adjust

", and

then press the

button to choose "

Self Cal

", entering the self-calibration procedure of

the instrument.

Function Menu

Setting

Description

BackLight

0% - 100%

Turn the

knob to adjust the backlight.

Graticule

Select the grid type

Menu Time

5 s - 50 s, OFF Set the disappear time of menu

Function Menu

Setting

Description

Self Cal

Carry out the self-calibration procedure.

Default

Call out the factory settings.

ProbeCh.

Check whether probe attenuation is good.

Содержание SDS-E Series











































































































Результаты поиска

Содержание SDS-E Series

Отзывы:

Похожие инструкции для SDS-E Series

Бренды по названию

Популярные бренды

Owon SDS-E Series, Руководство пользователя

Результаты поиска

Содержание SDS-E Series

Отзывы:

Похожие инструкции для SDS-E Series

Бренды по названию

Популярные бренды