Ortho-Clinical Diagnostics ID-MTS страница 21 Скачать руководство пользователя | Manualshive

Страница: 21 / 26

background image

ORTHO

™

Workstation for ID-MTS

™

Gel Cards Reference Guide

Pub. No.: J55700ENna

21

2013-09-04

Section 9 - Warranty

Section 9 - Warranty

Warranty Time Period

Ortho Clinical Diagnostics warrants the ORTHO

™

Workstation to function properly for one year

from date of shipment (from manufacturer storehouse). This warranty covers the purchaser of this
instrument and anyone else who owns it during the warranty period.

Warranty Repair Coverage

If this equipment does not function properly during the warranty period, please contact the
technical assistance OCD Customer Technical Services number provided by Ortho Clinical
Diagnostics or your distributor to arrange for service. The equipment will be replaced.

Limitations

OCD will not be responsible for any consequential or incidental damages resulting from the sale,
use or improper functioning of this equipment.

«
...
19
20
21
22
23
...
»

Содержание ID-MTS



























Отзывы:

Нет отзывов

Похожие инструкции для ID-MTS

Sportsound SSR-200

Бренд: Daktronics Страницы: 5

Бренд: DANLERS Страницы: 2

Бренд: Haas Automation Страницы: 26

GPSMAP 188 Sounder

Бренд: Garmin Страницы: 134

Бренд: Taurus Страницы: 24

Бренд: Ofa Bamberg Страницы: 80

ThermoTweez Handpiece TT-65

Бренд: Pace Страницы: 14

ST70 Instrument

Бренд: Raymarine Страницы: 12

Бренд: Raven Страницы: 73

Бренд: Tascam Страницы: 3

Бренд: RAB Lighting Страницы: 4

Бренд: campgo Страницы: 33

Бренд: Valcom Страницы: 6

Бренд: Vaisala Страницы: 60

Бренд: KUHN Страницы: 112

Бренд: Federal Signal Corporation Страницы: 31

Бренд: Furuno Страницы: 20

Бренд: SIGLENT Страницы: 188

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды