manualshive.com logo in svg

Ortho-Clinical Diagnostics ID-MTS, Справочное руководство

Поделиться
Скачать
Ortho-Clinical Diagnostics ID-MTS Скачать руководство пользователя страница 9

ORTHO

™

 Workstation for ID-MTS

™

 Gel Cards Reference Guide

Pub. No.: J55700ENna

9

2013-09-04

Section 3 - Installation & Specifications

Site Specifications 

Select a location for the ORTHO

™

 Workstation that is convenient for laboratory personnel to 

perform testing. The surface must be a stable, level, vibration-free surface, away from direct 
sunlight, free from dust, solvent and acid vapors and have an electrical outlet close enough to the 
instrument to permit power access without an extension cord. Do not expose it to heat or cold 
(close proximity to heating or air-conditioning systems). Never subject it to violent shaking or any 
other shock or impact. 

\

Environmental Requirements

Electrical Requirements 

The ORTHO

™

 Workstation is equipped with automatic sensing of input voltage within the range of 

100 – 240 V~, 50/60 Hz, single phase. Connect the instrument to the power outlet with the 
grounded three-prong power cord provided.

Ventilation Requirements 

There are no special ventilation requirements for this instrument.

Fuses:

2 required, T4AH250V - 4 Amp, 250V, 
ceramic, time delay, 5x20mm.

Cycle Speed:

1032 rpm ± 10 rpm

Speed Indicator:

4 digits 

Timing Indicator: 

4 digits 

Cycle Timing:

10 minutes ± 10 sec. 
(including ramp-up time) 

Centrifuge Card Capacity:

10 cards

Incubation Temperature:

37°C ± 2°C

Incubator Card Capacity:

20 cards (two sections of 10)

Noise Level Generated:

Maximum 50 dba at 1 meter (during normal 
operation)

WARNING: As with any electrical appliance, place the instrument AWAY from any

source of water, such as a laboratory sink. An electrical hazard may exist when

improperly using the ORTHO

™

 Workstation near water.

WARNING: Do not block access to the power cord or Stop button during

ORTHO

™

 Workstation operation.

Temperature:

15 – 30°C (59 – 86°F)

Relative Humidity: 

15 – 85% (non-condensing)

Содержание ID-MTS



























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды