Ortho-Clinical Diagnostics ID-MTS Скачать руководство пользователя

Страница: 5 / 26

ORTHO

™

Workstation for ID-MTS

™

Gel Cards Reference Guide

Pub. No.: J55700ENna

2013-09-04

Section 1 - Description

Section 1 - Description

Intended Use

The ORTHO

™

Workstation is intended to support the

in vitro

immunohematology testing of human

blood through the incubation and centrifugation of ID-MTS

™

Gel cards.

Overview

The ORTHO

™

Workstation is a combined bench top workstation providing incubation and

centrifugation, utilizing ID-MTS

™

Gel card Column Agglutination Technology. The ORTHO

™

Workstation includes (refer to Figure 1):

Figure 1: ORTHO

™

Workstation

Materials provided:

Materials required but not provided:

• ORTHO

™

Workstation

• Reference Guide

• Power Cord

• Balance card

• Photo calibrated tachometer

• Calibrated thin wire
temperature meter

•

ID-MTS

™

Gel card and reagents

listed in corresponding IFU

• A calibrated stopwatch or
equivalent

• Phillips screwdriver

Centrifuge Rotor

Centrifuge Lid

Incubator Lid

Balance Card

Holder

Centrifuge

Card Holder

Centrifuge

Start Button

Centrifuge

Stop Button

Incubator Timer

Up/Down Buttons

Incubator

Start/Stop Button

Incubator Temperature

Status Display

Incubator Block

Centrifuge

Lid Latch

Centrifuge Time

LED Display

Centrifuge RPM

LED Display

Power Cord and

Fuse Assembly

Incubator Time

LED Display

Содержание ID-MTS



























Результаты поиска

Содержание ID-MTS

Отзывы:

Похожие инструкции для ID-MTS

Бренды по названию

Популярные бренды

Ortho-Clinical Diagnostics ID-MTS, Справочное руководство

Результаты поиска

Содержание ID-MTS

Отзывы:

Похожие инструкции для ID-MTS

Бренды по названию

Популярные бренды