manualshive.com logo in svg

Ortho-Clinical Diagnostics ID-MTS, Справочное руководство

Поделиться
Скачать
Ortho-Clinical Diagnostics ID-MTS Скачать руководство пользователя страница 16

Section 6 - Troubleshooting and Error Codes

ORTHO

™

 Workstation for ID-MTS

™

 Gel Cards Reference Guide

16

Pub. No.: J55700ENna

2013-09-04

202

Setpoint High Error:

 The setpoint value read from the temperature controller’s was higher 

than expected.

203

Setpoint Calculated Low Error:

 The calculated temperature setpoint is less than the 

acceptable minimum. This could be caused by lab environmental temperature. Let the system 
stabilize for one hour, turn the instrument off then on.

204

Setpoint Calculated High Error: 

The calculated temperature setpoint is higher than the 

acceptable maximum. This could be caused by lab environmental temperature. Let the 
system stabilize for one hour, then turn the instrument off then on.

205

Temperature Sensor 1 Low Error:

 The temperature sensor value read from the temperature 

controller was lower than expected.

206

Temperature Sensor 1 High Error: 

The temperature sensor value read from the temperature 

controller was higher than expected.

207

Heater Controller Read Error:

 There was a failure reading from the temperature controller.

208

Heater Controller Write Error:

 There was a failure writing to the temperature controller.

†

Test is no longer valid

Содержание ID-MTS



























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды