ORTAL Clear 130 LS Скачать руководство пользователя

Страница: 34 / 67

Venting

General Venting Requirements

The fireplace operates using a direct vent system and require a co-axial direct vent pipe. The fireplace must be properly connected

to an approved vent system. Venting is not provided with the fireplace and must be sourced from one of the approved vent

manufacturers mentioned in the table below. Proper installation, use, and maintenance of venting is determined by and can be

acquired from the vent manufacturer.

Vent Requirements

Fireplace

Series

Vent Type

Vent Size

Approved Vent Manufacturers

Direct Vent

4x6 co-axial direct vent pipe

(4” interior, 6

” exterior)

Olympia: Ventis

DuraVent: Direct Vent Pro

ICC: EXCELDirect

BDM: Pro-Form Direct Vent System

Selkirk: Direct-Temp System

Enervex Power Vent

4x6 co-axial direct vent pipe

(4” interior, 6

” exterior)

Ortal Power Vent*

3x5 co-axial direct vent pipe

(3” interior, 5” exterior)

DuraVent: CVS line

110

120

130

150

170

200

250

Traditional

Wilderness

Direct Vent

5x8 co-axial direct vent pipe

(5-inch interior, 8-inch exterior)

Olympia: Ventis

DuraVent: Direct Vent Pro

ICC: EXCELDirect

BDM: Pro-Form Direct Vent System

Selkirk: Direct-Temp System

Enervex Power Vent

5x8 co-axial direct vent pipe

(5-inch interior, 8-inch exterior)

Ortal Power Vent

3x5 co-axial direct vent pipe

(3-inch interior, 5-inch exterior)

DuraVent: CVS line

Curve

Island

Direct Vent

5x8 co-axial direct vent pipe

(5-inch interior, 8-inch exterior)

Olympia: Ventis

DuraVent: Direct Vent Pro

ICC: EXCELDirect

BDM: Pro-Form Direct Vent System

Selkirk: Direct-Temp System

Enervex Power Vent

(see note below)

5x8 co-axial direct vent pipe

(5-inch interior, 8-inch exterior)

Power Vent: a fan-assisted direct vent system that boosts airflow for vent configurations with too much constriction. Review

“Vent Configuration Diagrams” section to determine if your fireplace needs a power vent. See the Ortal Power Vent Manual

for more details on power venting.

NOTE: The Curve and Island series fireplaces are not permitted for use with an Ortal Power Vent.

WARNING: Do not combine vent components from different vent manufacturers. Please follow the manufacturer’s

instructions for vent system installation.

Vent Installation

Venting must be installed to meet the requirements as detailed in the following sections in conjunction with the vent system

manufacturer’s installation instructions. Venting must be supported by the structural surrounding and not by the fireplace. Each offset

(elbow) must be strapped to reduce movement or possible disconnection.
The first section of venting must be secured to the fireplace starter collar with a minimum of 3 sheet metal screws no longer than

”.

DO OT use silicone to seal the sections. If sealing is required by the vent manufacturer or local code, use Mil-Pac sealant.

WARNING: Do not combine vent components from different vent manufacturers. Please follow the manufacturer’s

instructions for vent system installation.

Содержание Clear 130 LS




































































Результаты поиска

Содержание Clear 130 LS

Отзывы:

Похожие инструкции для Clear 130 LS

Бренды по названию

Популярные бренды

ORTAL Clear 130 LS, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Clear 130 LS

Отзывы:

Похожие инструкции для Clear 130 LS

Бренды по названию

Популярные бренды