Opticon LG2 Series Скачать руководство пользователя страница 42

Страница: 42 / 113

LG2 User’s Manual 25-ULG2MU01-02 -

Save Settings

LG2 User’s Manual 25-ULG2MU01-02 -

Save Settings

To find out the Reader ID and firmware version, open a text editor program (i.e. Notepad, Microsoft
Word...) and read the following barcode:

Note:

For units with a Bluetooth Radio, the Reader ID is also your Bluetooth Radio PIN #.

Reader ID and Firmware

You will get a text string with your firmware version and LG2 ID number (see below):

Xap/iVVVVWWWWXXXXSSSSSSSSSSPXX

Xap/i - Opticon Internal ID (not applicable)

VVVV is the application firmware version number

WWWW is the bootloader firmware version number

XXXX is the radio firmware version number

SSSSSSSSSS Reader’s serial number (ten digits)

P is “A” if running firmware is the application, “B” if bootLoader

XX - Opticon Internal ID (not applicable)

Example:

Xap/i2098201206000010002363A06

Note:

Opticon will periodically release new firmware for LG2 units. For information on latest

firmware versions, call Opticon at (800) 636-0090. To upgrade the firmware please visit Opticon
website at http://www.opticonusa.com and follow instructions.

5.1 - Reader ID and Firmware Version

Содержание LG2 Series


















































































































Результаты поиска

Содержание LG2 Series

Отзывы:

Похожие инструкции для LG2 Series

Бренды по названию

Популярные бренды

Opticon LG2 Series, Руководство пользователя

Результаты поиска

Содержание LG2 Series

Отзывы:

Похожие инструкции для LG2 Series

Бренды по названию

Популярные бренды