Opticon LG2 Series Скачать руководство пользователя страница 33

Страница: 33 / 113

LG2 User’s Manual 25-ULG2MU01-02 -

Save Settings

LG2 User’s Manual 25-ULG2MU01-02 -

Save Settings

4.1 - Introduction

The following chapter will allow a user to change the symbology settings on the LG2. To reset the unit to
factory defaults or to save the current settings please scan one of the barcodes below:

Save Settings

Reset to USB Factory Defaults

Clear All CodeXML Rules

Reset to PS2 Factory Defaults

Note:

If you do not save your settings and the LG2 loses power you will lose your settings.

4.2 - Aztec Symbology

Scan the following codes to enable/disable Aztec symbology settings:

Aztec On

Aztec Off (Default)

Sample Aztec Code

4.3 - Codabar Symbology

Scan the following barcodes to enable/disable Codabar symbology settings:

Codabar On (Default)

Codabar Off

Sample Codabar

Not all settings will be

reset with this barcode.

Non-standard inks

and radio settings will not

be reset.

Not all settings will be

reset with this code.

Non-standard inks

and radio settings will not

be reset.

Содержание LG2 Series


















































































































Результаты поиска

Содержание LG2 Series

Отзывы:

Похожие инструкции для LG2 Series

Бренды по названию

Популярные бренды

Opticon LG2 Series, Руководство пользователя

Результаты поиска

Содержание LG2 Series

Отзывы:

Похожие инструкции для LG2 Series

Бренды по названию

Популярные бренды