Opticon LG2 Series Скачать руководство пользователя страница 44

Страница: 44 / 113

LG2 User’s Manual 25-ULG2MU01-02 -

Save Settings

LG2 User’s Manual 25-ULG2MU01-02 -

Save Settings

5.4.1 - Bluetooth Radio - Auto Connect

Auto Connect:

After coming out of sleep mode or after powering up (need to save the connection) the

LG2 tries to auto connect with the last Bluetooth radio it was connected with. You may always connect

by scanning a quick connect code.

Scan the following barcodes to enable or disable Auto Connect feature for the Bluetooth radio:

Bluetooth Radio Auto Connect On (Default)

Bluetooth Radio Auto Connect Off

5.4 - Bluetooth Radio Interface (con’t)

Auto Disconnect:

This feature is used when multiple LG2 units are connecting to the same Bluetooth

Radio. By enabling Auto Disconnect the LG2 radio disconnects after each data transmission, allowing

other radios to connect.

Scan the following barcodes to enable or disable Auto Disconnect feature for the Bluetooth radio:

Bluetooth Radio Auto Disconnect On

Bluetooth Radio Auto Disconnect Off (Default)

5.4.2 - Bluetooth Radio - Auto Disconnect

RF Two Way Mode (con’t) -

of software called CodeXML Router Bluetooth Edition (BE) that auto-

matically provides packet protocol verification. CodeXML Router BE allows for end-to-end Bluetooth
handshakes that eliminate the case of out-of-range data loss.

Scan the following barcodes to set the Radio Frequency (RF) communication settings:

RF One Way Mode - Max Range (Default)

RF One Way Mode - Max Reliability

RF Two Way Mode

Содержание LG2 Series


















































































































Результаты поиска

Содержание LG2 Series

Отзывы:

Похожие инструкции для LG2 Series

Бренды по названию

Популярные бренды

Opticon LG2 Series, Руководство пользователя

Результаты поиска

Содержание LG2 Series

Отзывы:

Похожие инструкции для LG2 Series

Бренды по названию

Популярные бренды