Opticon LG2 Series Скачать руководство пользователя страница 55

Страница: 55 / 113

LG2 User’s Manual 25-ULG2MU01-02 -

Save Settings

LG2 User’s Manual 25-ULG2MU01-02 -

Save Settings

Scan the following barcodes to set delay time between scans:

0 Seconds (Default)

1 Second

3 Seconds

7.4.2 - Continous Scan - Trigger Delays

7.4 - Continous Scan

Scan the following barcodes to turn continous scanning on/off:

Both Near & Far Field On

Near Field Only On

Far Field Only On

Off (Default)

Note:

This function is only reccommended for short term use because of battery consumption. See section

7.4.1 for Sleep Time Out Settings

Will only work in versions 2098 and above. Scan one of the codes below to set the amount of time a cabled
LG2 will operate in continous scan mode before entering sleep mode:

Cabled - 2 hours (Default)

Cabled - Always

Scan one of the codes below to set the amount of time a uncabled LG2 will operate in continous scan
mode before entering sleep mode:

Uncabled - 5 minutes (Default)

Uncabled - 15 Minutes

Uncabled - 30 Minutes

Note:

This fuction is only reccommended for short term use because of battery consumption.

7.4.1 - Continous Scan - Sleep Time Out

Содержание LG2 Series


















































































































Результаты поиска

Содержание LG2 Series

Отзывы:

Похожие инструкции для LG2 Series

Бренды по названию

Популярные бренды

Opticon LG2 Series, Руководство пользователя

Результаты поиска

Содержание LG2 Series

Отзывы:

Похожие инструкции для LG2 Series

Бренды по названию

Популярные бренды