Opticon LG2 Series Скачать руководство пользователя страница 38

Страница: 38 / 113

LG2 User’s Manual 25-ULG2MU01-02 -

Save Settings

LG2 User’s Manual 25-ULG2MU01-02 -

Save Settings

4.15 - Micro PDF 417 Symbology

Scan the following barcodes to enable/disable micro PDF 417 symbology settings:

MicroPDF417 On

MicroPDF417 Off (Default)

Sample MicroPDF417

The Macro PDF 417 function has the following limitations:

You can scan non-MacroPDF417 in the middle of a MacroPDF417 file. They will

be uploaded immediately. The incomplete MacroPDF417 segments will be buffered.

Scanning a MacroPDF417 barcode with a file ID different than the MacroPDF417 segments

already stored will cause the stored segments to be deleted(aborted) and you will hear

beeps. The new file starts with this barcode.

The LG2 only support up to 16 file segments. When the buffered segments reach 16 and

the file is still not complete, you will hear 3 beeps and all the buffered segments will be

deleted.

You can not scan a segment of the same file more than once.

Note:

The MacroPDF 417 feature may only be utilized with firmware version 1242 or greater.

4.14 - PDF 417 Symbology (con’t)

All postal barcodes default settings are OFF. Scan the following barcodes to enable the appropriate
Postal symbology:

Note:

If you wish to change which Postal barcode is activated, you MUST scan the disable all postal

barcodes symbol and then scan your desired symbology.

Australian Post On

Japan Post On

KIX

Planet On

Postnet On

Postnet and Planet On

4.16 - Postal Symbologies

Содержание LG2 Series


















































































































Результаты поиска

Содержание LG2 Series

Отзывы:

Похожие инструкции для LG2 Series

Бренды по названию

Популярные бренды

Opticon LG2 Series, Руководство пользователя

Результаты поиска

Содержание LG2 Series

Отзывы:

Похожие инструкции для LG2 Series

Бренды по названию

Популярные бренды