Opex Perfect Pick Cortex Скачать руководство пользователя страница 36 | Manualshive

Страница: 36 / 134

Opex Perfect Pick Cortex Скачать руководство пользователя страница 36

36

Safety

Perfect Pick® Cortex™ Operator Manual

OPEX Corporation

2.6.4. Fully de-energizing AC power

At most customer sites, the PPIWS is hard-wired to a dedicated AC main
disconnect switch located near the machine. To safely de-energize the PPIWS
AC Distribution enclosure, the incoming power must be shut off by turning off
and locking out the customer’s main disconnect switch.

An Authorized Employee or qualified electrician must proceed as follows:

1.

Complete all steps under

“LOTO - Machine Maintenance and Repair” on

2. Customer’s site maintenance personnel only:

shut off the main AC

disconnect switch and install a Lockout-Tagout device (Figure 2-10).

Figure 2-10: Example- AC main disconnect with Lockout/Tagout

WARNING

Contact the customer’s site supervisor before attempting this procedure. Only
the customer’s authorized site maintenance personnel are permitted to shut
off the site AC power.

«
...
34
35
36
37
38
...
»

Содержание Perfect Pick Cortex







































































































































Отзывы:

Нет отзывов