OnRobot RG2-FT Скачать руководство пользователя страница 46 | Manualshive

Страница: 46 / 84

background image

rg_grip(r5, 40, rg_index_get())

→ This will open the Gripper 5mm with the

target force set at 40N.

If two RG grippers attached, use:

rg_grip(rg_Width_5, 40, 1)

→ for primary

rg_grip(rg_Width_se5, 40, 2)

→ for secondary

6.4. TCP Configuration

TCP is the abbreviation of the Tool Center Point.

TCP is a point that is in the beginning (by default) located at the
middle point of the UR's tool flange. This is an important point
during robot programming since UR's Move commands are
always referenced to a given TCP point and rotations could only
be carried out about these points.

If a tool is attached to the robot, it makes easier for the
user to change that point to the tool's “end” point (see
illustration on the left).

In this way it is easy to rotate the tool while the
workpiece is being stationary in space (see illustration
on the right).

More than one TCP point could be defined but at a
given time only one TCP can be active. In UR, it is called
the Active TCP.

By default, UR's Move commands are always recording
the Waypoints according to the Active TCP.

For further info about the UR's TCP handling read the
UR's Manual.

How “far” the TCP needs to be moved to be at the “end” of the OnRobot tools could be found
in the

8.3. COG, TCP

section.

Since, it could be hard to enter these values by hand, OnRobot provides two ways to get
these parameters configured for you:

•

Static TCP mode - Recommended to be used

•

Dynamic TCP mode

The mode could be selected on the TCP panel in the OnRobot Installation (see in the

URCap Setup

setup section).

In the following these two modes will be described.

Static TCP Mode

In this mode the user can manually change the Active TCP based on the predefined OnRobot
TCP options:

OPERATION

46

«
...
44
45
46
47
48
...
»

Содержание RG2-FT





















































































Отзывы:

Нет отзывов

Похожие инструкции для RG2-FT

Бренд: OSEPP Страницы: 40

Бренд: ABB Страницы: 19

Бренд: TTS Страницы: 19

Бренд: HobbyTronics Страницы: 6

Toby Tire Robot

Бренд: Robotronics Страницы: 61

Patches & Pumper

Бренд: Robotronics Страницы: 63

Бренд: Budget Robotics Страницы: 9

Бренд: GreyRobotics Страницы: 21

Бренд: Totem Страницы: 55

Бренд: Vex Robotics Страницы: 48

Бренд: EasyRobotics Страницы: 11

Бренд: Rainbow Robotics Страницы: 440

Бренд: Nexus Automation Страницы: 128

Бренд: Raspberry Pi Страницы: 20

SpotPack IRB 6620

Бренд: ABB Страницы: 290

Бренд: ABB Страницы: 610

FlexLoader SC 6000

Бренд: ABB Страницы: 284

Feather Duster V2

Бренд: ABB Страницы: 192

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды