15
Installation & Operation Guide: Oncam Grandeye 360
o
Evolution Camera Range
Version 2.4 | January 2014 | Oncam Grandeye, 115 Hammersmith Road, London. W14 0QH. UK
T: +44 (0)20 7371 6640 | E: [email protected] | W: www.oncamgrandeye.com
The Camera Module is installed by rotating the camera into the cleat in the
base plate and fastening it in place with the captive thumb screw. Wires
should be routed such that they do not cross over the lens area when the
trim ring is attached.
A BNC video connector is provided for camera testing and providing a
spot monitor video output. If used, then check the dip switch settings for
either PAL or NTSC video. Once testing is completed, the BNC test cable
can be removed. The cover can then be fastened in place by orienting the
elongated ‘ears’ of the cover with the elongated tabs on the mounting
plate and pushing it on until it snaps in place. There are guide tabs that will align the cover as it is pushed into
place. To remove the cover, just grasp the sides of it and pull away from the mounting surface.
For installations where the wiring is from the side, there is a thin section of plastic on the cover at one end, this can
be easily removed with a pair of pliers. Wiring in this case should be routed through the tunnel in the mounting
plate.
4.1.4
Pendant Mounting
For applications that require the enclosure to be mounted below the ceiling plane, the accessory pendant adapter
can be used to adapt the enclosure to M32 male pipe threads. This is an optional installation kit and can be
purchased from Oncam Grandeye.
Wiring is fed down inside the pipe and enters the enclosure from the back. Before mounting the adapter to the
pipe, the adapter is to be mounted to the mounting plate, there are two snap features in the pendant adapter that
allow the mounting plate to be temporarily fastened to the mounting plate. The mounting plate should then be
secured to the pendant adapter with the two thread forming plastite screws, which are screwed in to the two
bosses in the pendant adapter. Mount the pendant adapter to the M32 pipe and pull wires through the mounting
plate as before. Wiring and cover installation is then the same as a ceiling application.
4.1.5
Wall (Vertical Surface) Mounting
The Evolution housing may be mounted directly to a vertical surface. The wall mount is used for mounting to a
vertical surface with the housing in a horizontal attitude (wall, pole, or building corner). The indoor pendant adapter
as well as the wall mount to pendant adapter is required.
The base plate is used to adapt the wall mount to recessed wiring boxes or to uneven surfaces. Wiring is passed
through the plate. It is then fastened to the mounting surface or box with appropriate fasteners. The mounting cleat
is then attached to the base plate by placing the cleat over the two threaded studs that protrude from the base
plate and fixing it with nuts provided. It is not symmetrical so the part has an arrow stamped on it. The arrow must
point upward for proper installation. The wiring is passed through the mount and then the top is hooked over the
upper cleat and lowered over the bottom cleat. The mount is secured to the cleat with the two socket head set
screws using a 3/32” hex wrench.
When mounting to a studded wall or solid wall and where no electrical box is used, the base plate is not needed.
With this method the cleat plate can be mounted directly to the wall/stud and the wiring is passed through the cleat
plate via the holes provided on either side so that the wire can run on either side of a wall stud. Likewise, if the
installation is to a pole or corner mount, the base plate is not needed.
For mounting to a wall surface where wiring cannot be fed though the wall, a flexible conduit entry can be created to
the wall mount on the left and right sides of the part. There is a flat area on both sides for this purpose. It will be
necessary to drill a hole in to the mount arm in these locations for the appropriate hole size for the conduit adapter
of choice. It is recommended that the conduit hole is created prior to installing the mount to the cleat plate. It is
suggested that the connection be done with a length of flex conduit.
