distance can be less than two pixels.
Edge
level
0 to 100
[50]
Specify the density change level to be
detected as edges.
When the Measurement result is lower than
the actual number, please tune down the
Edge level (or the min level). Whereas the
Measurement result is higher than the actual
number, please tune up the Edge level (or the
min level).
User's Manual, "Edge Measurement"
3. If necessary, in the "Noise removal" area, tap [...] and specify a value for each
item.
How to input a value:
User's Manual, "Inputting a Value"
The "Noise level" value can be adjusted by dragging the slider or by tapping the
buttons at both ends of the slider.
The "Noise width" value can also be adjusted by tapping [<] and [>].
Table: Measurement (Edge Pitch) - Noise Removal
Setting
Item
Set Value
[Factory
Default]
Description
Noise
level
0 to 442
[5]
This item obtains the maximum and minimum values of
the color/density in the edge detection region. If the
difference is less than the noise level, no edge is assumed
to exist. When the detection is affected by noise, increase
the value.
User's Manual, "Noise Level"
Noise
width
0 to 9999
[0]
Specify the width of noise.
When the color/density distribution falls below the edge
level within the noise width from the first detected edge
position, the detected points are considered as noise. When
the detection is affected by noise, increase the value.
User's Manual, "Noise Width"
Содержание FZ2 Series
