When using an all-in-one camera, specify whether to use data inside the
camera as 3D coordinate setting parameters.
Table: 3D Setting - 3D Coordinates (3D Camera Image Input)
Item
Set Value
[Factory
Default]
Description
The data camera has
When using an all-in-one camera, specify
whether to use data inside the camera as 3D
coordinate setting parameters.
[Checked]
The data inside the camera is used as 3D
coordinate setting parameters.
Availableness
Unchecked
The newly obtained data is used as 3D coordinate
setting parameters.
4. Set the "Optical condition setting" and "Sampling condition" as necessary.
Table: 3D Setting - 3D Coordinates (3D Camera Image Input)
Item
Set Value
[Factory Default]
Description
Focal length of
lens
1.0 to 999.9
[16.0]
Set the focal length of the
camera lens.
Optical
condition
setting
Photographing
ring
[0.0] to 999.9
Set the photographing ring of
the camera.
Sampling
condition
Sampling point
o
5 x
5
o
7 x
7
o
9 x
9
o
11 x
11
o
[7 x
Select the number of
sampling points for sampling
measurement. Unit is n points
x n points.
Set up [3D coordinates] in
the whole field of view.
The correspondence between
the field of view and
sampling points are shown
Содержание FZ2 Series
