manualshive.com logo in svg

Omron CS1W-CT021, Руководство по эксплуатации

Поделиться
Скачать
Omron CS1W-CT021 Скачать руководство пользователя страница 6

"!!

TABLE OF CONTENTS

PRECAUTIONS ...............................................................................................   xi

1

Intended Audience........................................................................................................................................................   xii

2

General Precautions......................................................................................................................................................   xii

3

Safety Precautions ........................................................................................................................................................   xii

4

Operating Environment Precautions............................................................................................................................   xiii

5

Application Precautions...............................................................................................................................................   xiv

6

EC Directives...............................................................................................................................................................   xvi

SECTION 1
Introduction.......................................................................................................   1

1-1

Features and Functions ............................................................................................................................................

  2

1-2

Basic Configuration.................................................................................................................................................

  5

1-3

Specifications and Characteristics...........................................................................................................................

  7

1-4

Quick Start Up Reference Guide .............................................................................................................................

  14

1-5

Operating Procedure Guidelines..............................................................................................................................

  20

1-6

Application Areas....................................................................................................................................................

  23

SECTION 2
Components, Installation and Wiring.............................................................   25

2-1

Components and Switch Settings ............................................................................................................................

  26

2-2

Installation ...............................................................................................................................................................

  30

2-3

Wiring ......................................................................................................................................................................

  32

SECTION 3
Operation and Configuration ..........................................................................   45

3-1

Overview .................................................................................................................................................................

  46

3-2

Counter Types..........................................................................................................................................................

  47

3-3

Input Signal Types ...................................................................................................................................................

  55

3-4

Digital Input Functions............................................................................................................................................

  58

3-5

Output Control.........................................................................................................................................................

  65

3-6

Reset Signals ...........................................................................................................................................................

  79

3-7

Extra Functions........................................................................................................................................................

  81

SECTION 4
Exchanging Data with CPU .............................................................................   91

4-1

Overview .................................................................................................................................................................

  92

4-2

Memory Allocation .................................................................................................................................................

  94

4-3

IOWR-Instruction....................................................................................................................................................   124

4-4

IORD-Instruction.....................................................................................................................................................   126

4-5

Supported IOWR/IORD-Instructions......................................................................................................................   128

4-6

Interrupts..................................................................................................................................................................   135

SECTION 5
Error Processing, Maintenance and Inspection............................................   141

5-1

Error Indicators........................................................................................................................................................   142

5-2

Error codes...............................................................................................................................................................   143

W902-E2-03.book  Seite vii  Donnerstag, 7. Oktober 2004  2:06 14

Содержание CS1W-CT021










































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды