manualshive.com logo in svg

Omron CS1W-CT021, Руководство по эксплуатации

Поделиться
Скачать
Omron CS1W-CT021 Скачать руководство пользователя страница 43

0)>4)*#*'+-%*.-3?('$5-3#''(*2+

Section 2-1

%+

2-1-3

Counter Type Switch 

The Counter Type Switch, at the back of the Unit, is used to set the Counter Type
for every individual Counter separately. By default all Counters are set to Simple
Counter.

The following table shows how the Counters can be configured:

* CS1W-CT041 High-speed Counter Unit only.

After having set the DIP switch of the Counter to ON, further selection between
Circular and Linear Counter, is done by DM-setting. Counters that are configured
for Circular/Linear Counter can make use of all the features that the High-speed
Counter Unit offers. More information on Circular and Linear Counters can be
found in 3-2-2 

"Circular Counter"

 and 3-2-3 

"Linear Counter"

 respectively. 

The Simple Counter is an extra feature of the High-speed Counter Unit, that ena-
bles an easy and fast set-up of the Unit since no (DM-) configuration settings have
to be made (all default (=0000) DM-settings are used). Consequently for Simple
Counters only a reduced subset of all the features that the Unit offers are availa-
ble. For further details about the Simple Counter and the features supported, see
3-2-1 

"Simple Counter"

. 

!Caution

Since the Counter Type Switch is located at the back of the Unit, always turn OFF
the power to the PLC before installing or removing the Unit.

Pin

Counter

Position

Type

1

#1

ON

Circular/Linear Counter

OFF

Simple Counter

2

#2

ON

Circular/Linear Counter

OFF

Simple Counter

3*

#3

ON

Circular/Linear Counter

OFF

Simple Counter

4*

#4

ON

Circular/Linear Counter

OFF

Simple Counter

ON Position

OFF Position

W902-E2-03.book  Seite 28  Donnerstag, 7. Oktober 2004  2:06 14

Содержание CS1W-CT021










































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды