manualshive.com logo in svg

Omron CS1W-CT021, Руководство по эксплуатации

Поделиться
Скачать
Omron CS1W-CT021 Скачать руководство пользователя страница 100

FG'"%-,&*$'()*+

Section 3-7

+(

Configuring Rate 
Measurement

Rate Measurement can be configured by setting the Time-Window between 1 ms
and 9999 ms (BCD). By default (=0) the Counters are configured to have no Rate
Measurement.

Rate Ranges

Besides the capability to measure (positive and negative) Rate Values for every
Counter two Rate Ranges (Rate Range 0 and 1) can be configured. The Rate
Ranges offer you the opportunity to undertake specific action (i.e. control the Unit
Output Pattern) when the measured Rate Values have entered a Rate Range.
Rate Ranges can represent Frequency Ranges or Rotational Speed Ranges,
making it possible to undertake action at (too high or too low Alarm) Frequencies
or Rotational Speeds.

The Data of every Rate Range is contained by 4 double words:

•

Lower Rate Range Limit, specifying the Lower Rate Limit of the Rate Range

•

Upper Rate Range Limit, specifying the Upper Rate Limit of the Rate Range

•

Output Set Pattern, specifying which Outputs must be Set if the measured
Rate Value is within the Lower- and Upper Rate Range Limits

•

Output Reset Pattern, specifying which Outputs must be Reset if the meas-
ured Rate Value is within the Lower- and Upper Rate Range Limits

The Upper Rate Range Limit must be greater than the Lower Rate Range Limit.
The Unit will generate an error if the Upper Rate Range Limit 

≤

 Lower Rate Range

Limit (refer to 5-2 

"Error codes"

 for more details). Every Rate Range can be ena-

CNT1:

CNT1:

CNT1:

CNT1:

m+39

m+84

m+129

m+174

Time-Window:

0000

(BCD)

 = No Rate Measurement

0001-9999

(BCD)

 = Time-Window in milliseconds

15 14 13 12 11 10

9

8

7

6

5

4

3

2

1

0

Time

Rate Value

Alarm-Area

Rate Range 0 Upper Limit

Rate Range 0 Lower Limit

Rate Range 1 Upper Limit

Rate Range 1 Lower Limit

Time-Window

Alarm-Area

Time

W902-E2-03.book  Seite 85  Donnerstag, 7. Oktober 2004  2:06 14

Содержание CS1W-CT021










































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды