Omron B5L Скачать руководство пользователя страница 15

Страница: 15 / 72

Chapter 1 Overview

1-3 Specifications

3D TOF Sensor Module B5L User's Manual (No. E596)

1-3 Specifications

Ratings/Performance Specifications

Item

Specifications

Note

Operating range

0.5m to 4m

Detection resolution Approx. 0.3°

Horizontal detection

range (angle of view) 87° min.

Vertical detection

range (angle of view) 67° min.

Light source

LED, near-infrared ray of 940nm

Distance precision

2%(

4cm) max.

at 2m, center block, 10 x 10 pixel

Notes 1 & 2

Repeatability

1%(

2cm) max.

at 2m, center block, 10 x 10 pixel

Notes 1 & 2

Frame rate

10fps

Note 1

Supply voltage

DC24V ±10% 3A

Power consumption
(current consumption)

Average at measurement: 7.2W 0.3A
Maximum: 72W 3A (informative)

Note 1

Ambient
temperature

In use: 0 to +50

°C

Storage: -20 to +60

°C

(with no icing or condensation)

Ambient humidity

In use & storage: 35 to 85 %RH max.
(no dew condensation)

Operating illumination

environment

500lx max.

Vibration resistance

10 to 150Hz: acceleration of 50m/s

, double amplitude of 0.7mm max.

8 min. 3 sweeps each in X, Y, and Z directions

Shock resistance

300m/s

for 3 times each in X, Y, and Z directions

Dimensions

103 × 64.3 × 43.1 mm
Approx. 108.6 x 64.3 x 43.1mm (connector included)

Degree of protection IEC60529 IP10

Weight

Approx. 305 g

Material

Frame: Aluminum die-cast
Cover: Polycarbonate (PC)
Filter: Acrylic resin (PMMA)
Heat sink: Aluminum

Communications

USB2.0 CDC class

Start-up period

30 seconds max.

Note 3

Warm-up period

Approx. 30 minutes

Note 4

Note 1:

- When stable in OMRON's measurement environment
- Ambient temperature: 25

°C

- Operation mode: Normal mode (default)
- Exposure time setting: 850 (default)
- LED emission frequency ID: 8 (default)

Note 2:

- Target object: 70% reflectivity (white paper)
- Distance precision and repeatability are based on the following conditions:

Distance precision: Average of 100 measurements of 10 x 10 pixels in the center (10,000 data in
total)
Repeatability: Standard deviation of 100 measurements of 10 x 10 pixels in the center (10,000
data in total)

Note 3:

Time from power-on to when communications becomes available

Note 4:

Time from power-on to when the performance becomes stable

Содержание B5L









































































Результаты поиска

Содержание B5L

Отзывы:

Omron B5L, Руководство пользователя, Страница: 15 / 72

Результаты поиска

Содержание B5L

Отзывы: