OmniCell ERB Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 112

background image

© 2011 Omnicell, Inc.

External Return Bin Installation and Service Guide/

67-2038 Rev D

1-1

Overview

This document provides installation and service instructions for the External Return Bin (ERB)
on the G3 cabinets, the G3 cabinets with the G4 electronics box, and the G4 cabinets.

The ERB is used to collect unused medication after it has been issued to a patient. Only one return
bin is supported per cabinet.

The ERB can be mounted to:



OmniRx Color Touch cabinets



OmniTT Color Touch cabinets



Half-Cell Color Touch cabinets



One-, two-, and three-cell Color Touch cabinets



Anesthesia Workstations



Walls



Table tops

The ERB comes built with a standard 4-foot cable mounted on the right side of the bin.

Software Requirements

The cabinet to which the ERB is attached must be running Color Touch 5.3 or higher.

Software Configuration Options

Refer to the Color Touch user guide of the version on the cabinet for the options that support the
External Return Bin.

Tools

The following tools are needed to install or mount the External Return Bin:



Nut driver (5/16", 11/32", and 1/4")



Allen wrench (3/32", 9/64" and 5/32")



Crescent wrench



T8 Torx driver



T10 Torx driver



T15 Torx driver



T20 Torx driver



Phillips screwdriver #2 for the ERB handle

«
...
3
4
5
6
7
...
»

Содержание ERB

















































































































Отзывы:

Нет отзывов

Похожие инструкции для ERB

Бренд: B&K Страницы: 12

Бренд: CAE Healthcare Страницы: 108

Бренд: Cannon Страницы: 36

Бренд: Hacker Страницы: 2

Бренд: J.P. SELECTA Страницы: 8

Бренд: Haemonetics Страницы: 134

Бренд: Hadeco Страницы: 72

Бренд: IBEX Страницы: 4

Бренд: Jaga Страницы: 32

Бренд: Nederman Страницы: 89

Бренд: Nederman Страницы: 71

Бренд: Nederman Страницы: 131

Бренд: X-Cite Страницы: 2

Бренд: Tascam Страницы: 3

Бренд: Vahle Страницы: 36

Бренд: Vahle Страницы: 20

Бренд: Vacon Страницы: 102

Бренд: Yamaha Страницы: 45

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды