OmniCell ERB Скачать руководство пользователя страница 42

Страница: 42 / 112

2-32

Installation Instructions

Installation on G3 Cabinets

External Return Bin Installation and Service Guide

/67-2038 Rev D

16. Fasten the ERB with four

#8 hex nuts

to the metal studs on the AWS mounting bracket.

Figure 2-85.

Securing the ERB

17. Rotate the lower plates. The open side of the left lower plate should face left. The open side of

the right lower plate should face down. This allows the left cover plate to protect the cables
being routed out of the ERB. The right cover plates will seal the cable openings on the right
side of the ERB.

Figure 2-86.

Orientation for left cover plates

Figure 2-87.

Left I/O cover plate

18. Re-install the I/O cover plates, being careful not to pinch any wires:

a. Place the I/O cover plates in position.

b. Secure the cover plates by screwing in the two 4-40 flat head fasteners.

19. Close and lock the access door.

Note:

The 6-pin white connector is not used.

6-pin

connector

Содержание ERB

















































































































Результаты поиска

Содержание ERB

Отзывы:

Похожие инструкции для ERB

Бренды по названию

Популярные бренды

OmniCell ERB, Инструкция по установке и обслуживанию

Результаты поиска

Содержание ERB

Отзывы:

Похожие инструкции для ERB

Бренды по названию

Популярные бренды