OmniCell ERB Скачать руководство пользователя страница 20

Страница: 20 / 112

2-10

Installation Instructions

Installation on G3 Cabinets

External Return Bin Installation and Service Guide

/67-2038 Rev D

Cabinet Preparation

1. Perform a graceful shutdown on the cabinet that is to have an ERB mounted.

2. Unplug the power cable.

3. Refer to the

Omnicell Drug Handling Policy and Procedures

for information regarding the

removal of drugs from the internal return bin drawer.

4. Empty the contents of the internal return bin drawer if it exists.

Installation on G3 Cabinets

This section contains ERB installation instructions for various G3 cabinet types. For installation
on G3 cabinets that have the new G4 E-box, see

“Installation on G3 Cabinets with G4 Console

Upgrade”

on page 2-40. For installation on G4 cabinets, see

“Installation on G4 Cabinets”

page 2-45.

This section describes installation procedures for the following:









“One-, Two-, and Three-Cell Cabinets”

on page 2-21



“Anesthesia Workstation (AWS) G3”

on page 2-26

OmniTT

Attaching the ERB to the OmniTT

on the right side of the OmniTT Color

Touch cabinet, then remove the original transport handle.

Figure 2-26.

Removing the original transport handle

Caution:

The pharmacist must be present when servicing any drawers where medication is present.

Important:

Once the ERB is enabled, the internal return bin is no longer accessible.

Содержание ERB

















































































































Результаты поиска

Содержание ERB

Отзывы:

Похожие инструкции для ERB

Бренды по названию

Популярные бренды

OmniCell ERB, Инструкция по установке и обслуживанию

Результаты поиска

Содержание ERB

Отзывы:

Похожие инструкции для ERB

Бренды по названию

Популярные бренды