OmniCell ERB Скачать руководство пользователя страница 31

Страница: 31 / 112

External Return Bin Installation and Service Guide/

67-2038 Rev D

Installation Instructions

2-21

Installation on G3 Cabinets

One-, Two-, and Three-Cell Cabinets

There are restrictions for installing an ERB on tall (1-, 2-, and 3-cell) cabinets:



The cabinet must have a PC box with a monitor.



An ERB can be installed on either side of a single cell cabinet with a PC box. Reconfigure the
ERB if installing it on the left side. See

“Cable Assembly Configuration”

on page 2-1 for

instructions.



Install the ERB on the right side of a multi-cell cabinet configuration which always has the
cabinet with the PC box on the right side.

Attaching the ERB to the One-, Two-, and Three-Cell Cabinets

1. Assemble the two

#8-32 x 3/8" socket head cap screws

to the modified transport handle in the

kit.

Figure 2-53.

Assembling the modified transport handle

2. Install the modified

transport handle

to the right side of the OmniSupplier cabinet.

Figure 2-54.

Installing the modified transport handle

Note:

A FlexLock cable can be used with an ERB.

Содержание ERB

















































































































Результаты поиска

Содержание ERB

Отзывы:

Похожие инструкции для ERB

Бренды по названию

Популярные бренды

OmniCell ERB, Инструкция по установке и обслуживанию

Результаты поиска

Содержание ERB

Отзывы:

Похожие инструкции для ERB

Бренды по названию

Популярные бренды