OmniCell ERB Скачать руководство пользователя страница 71 | Manualshive

Страница: 71 / 112

background image

© 2011 Omnicell, Inc.

External Return Bin Installation and Service Guide/

67-2038 Rev D

Installation Instructions

2-61

Installation on G4 Cabinets

6. Attach the ERB to the bracket using

four 8-32 button hd torx screws

.

Figure 2-148.

ERB attachment holes

7. Close and lock the ERB access door.

Cabling for the AWS G4

Cabling for the AWS G4 varies according to the configuration of the cabinet. When the ERB is
attached in the upper position, the cable is passed through a round hole in the top of the chassis.
In some cabinets with the ERB in the lower position, it is necessary to route the cable up the
outside back of the cabinet and pass it through a slot onto the top of the chassis. In some cabinets
with the ERB in the lower position, it is possible to pass the cable through an opening on the lower
side and up through the chassis to the top.

Cabling for the AWS G4 with the ERB Mounted in the Upper Position

1. Remove the worksurface from the AWS G4.

a. Move the monitor out of the way.

b. Use the cam lock

#2378 to unlock the worksurface.

c. Remove the two

front side screws

Figure 2-149.

AWS G4 worksurface with one of two screws removed

d. Slide the worksurface forward, then lift it up and away. Set it aside.

«
...
69
70
71
72
73
...
»

Содержание ERB

















































































































Отзывы:

Нет отзывов

Похожие инструкции для ERB

Бренд: Fender Страницы: 15

Бренд: J D Squared Страницы: 18

Бренд: Keiser Страницы: 2

Бренд: ECA Страницы: 3

Бренд: Nautilus Страницы: 12

Бренд: NEC Страницы: 54

Бренд: idiag Страницы: 12

Бренд: Quincy lab Страницы: 4

Бренд: HALDER Страницы: 2

Бренд: Hakko Electronics Страницы: 16

Бренд: Idex Страницы: 141

Бренд: IDEAL Networks Страницы: 8

Бренд: IDEAL Networks Страницы: 5

Varycolor MICRO 150HTI

Бренд: JB-Lighting Страницы: 18

Frontier FC5706

Бренд: OHAUS Страницы: 47

Бренд: Ocutech Страницы: 4

Бренд: Ultrawave Страницы: 30

Бренд: Ultrasound Technologies Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды