710.1760.00.04-05
22/05/2014
27
4.
Scroll through parameter list with the
and
arrows.
5.
Select the parameter you require.
6.
Press the
key to change its value.
7.
Change the value with the
and
keys.
8.
Press the
key again to confirm the new value. After a few seconds, the next parameter will
be displayed.
To exit programming: press the
+
keys when a parameter is displayed or wait 15 sec.
(timeout), without pressing any key.
NOTE:
The new parameter value is also saved if the
keys are not pressed during the timeout.
CAUTION: It is only possible to change the value of the parameters (configuration parameters) when the
chiller is in standby mode.
While programming, press the
key in order to scroll through the parameter codes or increase the val-
ue.
List of parameters that can be changed with the procedure described:
Standard value
Functioning
Code
Meaning
CHW
CHO
CHG
ST01
Set-point
15
25
-10
ST02
Differential
3
3
3
Please contact the manufacturer for further parameters
Displayed
Description
On our schemes
Pb1
Work probe temperature
SL
Pb2
Antifreeze probe temperature
SA
CONTROLLER TYPE “C” (CHW 682 TO CHW 3652; CHG 225 TO CHG 365)
The operating thermostat is supplied pre-adjusted according to the standard specifications of the chiller
listed in the supplement. The operating thermostat controls both the temperature regulating functions
and the other safety parameters (e.g. alarm management and the running time of the electric motors).
The complete list of parameters is not supplied to the customer because changes in certain parameters
may lead to problems affecting the reliability and properties of the chiller.
s
Instructions for changing the parameters required by the user:
Changing the SET-POINT:
1.
Press the
key for 3 seconds (the set-point starts to flash).
2.
Use the
and
arrows to change the SETPOINT.
3.
Press
or wait 15 sec. (timeout), without pressing any key.
To access the “Pr1” user level:
1.
Press the
+
keys for a few seconds (the
and
LEDs start to flash), the upper
display shows the first parameters with “PAS”.
2.
Press the
key to confirm and use the arrow keys
and
in order to enter the pass-
word “1”. Press the
key to confirm.
3.
Select the parameter you require.
Содержание CHG 08
