Oki C810 Скачать руководство пользователя страница 61

Страница: 61 / 253

44015503TH Rev. 1

60 /

Oki Data CONFIDENTIAL

3. INSTALLATION

3.8 Checking of paper used by the user

Load the media used by the user in the printer, make media weight/media type settings,

execute configuration/demo printing, and check the printout to make sure that no toner flakes

off.

Type

Weight or thickness

Settings on the operator panel

Setting*

for

[Media weight]

of the printer

driver

Media weight

(paper thickness)

Media type

(paper type)*

Plain

paper*

55-70 kg (64-82g/m

)

Light

Plain paper

Light

71-77 kg (83-90g/m

)

Medium Light

78-90 kg (91-105g/m

)

Medium

91-110 kg (106-128g/m

)

Heavy

111-175 kg (129-203g/m

)

Ultra heavy 1

176-189 kg (204-220g/m

)

Ultra heavy 2

Postcard*

—

Envelope*

—

Label

0.1 to under 0.17 mm

Heavy

Label

Label 1

0,17 to 0.2 mm

Ultra heavy 1

Label 2

*1: The factory default for the media type is [Light/OEL] [Medium Light/ODA].

*2: Media weight and type can be set on the operator panel and in the printer driver. The settings in

the printer driver take priority. Data is printed out in accordance with the setting on the operator

panel when [Auto selection] is selected in [Feed tray] or [Printer setting] is selected in [Media

weight].

*3: The weight of the paper supported for duplex print is 55-90 kg (64-105g/m

*4: It is not necessary to set media weight and type for postcards and envelopes.

Memo Print speed decelerates when [Heavy] or [Ultra heavy] of media weight or [Label

paper] of media type is set.

Содержание C810






























































































































































































































































Результаты поиска

Содержание C810

Отзывы:

Бренды по названию

Популярные бренды

Oki C810, Руководство по обслуживанию

Результаты поиска

Содержание C810

Отзывы:

Бренды по названию

Популярные бренды