Oki C810 Скачать руководство пользователя страница 147

Страница: 147 / 253

44015503TH Rev. 1

146 /

Oki Data CONFIDENTIAL

5. MAINTENANCE MENUS

5.4 setup after part replacement

ii. When the printer operates properly, the operator panel shows ONLINE.

When the printer has an error, it indicates an error, but the printer is

internally online, being ready to communicate.

2. When the EEPROM on a board to be removed cannot be accessed:

When SERvICE CALL 104 (Engine EEPROM Error) is displayed, or data cannot be

read from the EEPROM, after replacing the board to a new one, follow the following

procedure to perform operation by using Maintenance Utility:

(1) PU serial number setting (applicable Maintenance Utility operation manual,

section 2.4.1.1.2 about PU board setup)

A SAP serial number is assigned to the printer. The number is placed at

the top of the serial number label of the printer, consisting of total twelve

characters -- two characters that indicates a production place, two characters

that indicates a month and year, six characters that indicates a manufacture

number (sequence number) and two characters that indicates revision number.

• The PU serial number is ten characters from the SAP serial number. The

rest two characters are the revision number.

• The PU serial number is set in the PU serial number setting window

described in section 2.4.1.1.2.1 of the Maintenance Utility operation manual,

section 2.4.1.1.2 about PU board setup functionality.

• To assign a PU serial number to the printer, in the PU serial number setting

window, enter eleven characters, i.e. ten characters preceded by a single-

byte zero (0) (note a read PU serial number is ten characters). As shown in

the following serial number label example, the ten characters are the printer’

s the SAP serial number excluding the revision number.

The following describes the adjustments necessary after part replacement:

Replaced part

Adjustment

LED head

Note)

Not necessary.

Drum cartridge (yellow, magenta,
cyan or black)

Not necessary.

Fuser unit

Not necessary.

Belt unit

Not necessary.

PU board

Copying information stored in EEPROM, which
requires utility software.

CU board

EEPROM replacement, which uses EEPROM
intended for use in a user printer.

Note) See section 4.2.6, LED Assy. for compatibility of replacement LEDs with the

LEDs to be replaced with them, and identification of those LEDs.

5.4.1 notes on engine control board replacement

1. When the EEPROM on a board to be removed can be accessed (when SERvICE

CALL 104 (Engine EEPROM Error) is not displayed):

(1) Using the PU board replacement function of Maintenance Utility (Maintenance

Utility operation manual, section 2.4.1.1.1 about PU board replacement

functionality), remove information from the EEPROM, and temporarily store it

onto an HDD of the computer where the utility is operated.

(2) Using the PU board replacement function of Maintenance Utility (applicable

Maintenance Utility operation manual, section 2.4.1.1.1 about PU board

replacement functionality), copy the information into the EEPROM on a

replacement board.

Note! When removing or writing information from/into EEPROM by using

Maintenance Utility, use the procedure shown below to place the printer to the

Forced ONLINE mode before accessing the EEPROM. An error message is

displayed even in the forced ONLINE mode when the printer has an error.

i. When turning on the printer, press and hold down the BACK, MENU down-

arrow ( ) and ENTER buttons in combination until STATUS MODE appears

on the operator panel.

Ten characters to enter, edited to eleven characters,

preceded by single-byte zero (0) (0AE01234567)

Revision number

Serial number label example

Содержание C810






























































































































































































































































Результаты поиска

Содержание C810

Отзывы:

Бренды по названию

Популярные бренды

Oki C810, Руководство по обслуживанию

Результаты поиска

Содержание C810

Отзывы:

Бренды по названию

Популярные бренды