manualshive.com logo in svg

Oki C810, Руководство по обслуживанию

Поделиться
Скачать
Oki C810 Скачать руководство пользователя страница 205

44015503TH  Rev. 1 

204 /

Oki  Data  CONFIDENTIAL

7.  TROUBLESHOOTING PROCEDURE

Check item

Check work

Action to be taken 

at NG

(11-2-2) Temperature increase of fuser unit

Installation position 
of the upper 
thermistor

 Check if the upper thermistor is installed in the 
far position from the specified position or not 
causing detection of the lower temperature than 
the actual temperature of fuser unit. 
Remove the heater cover, and check warpage of 
sensor by visual inspection. 

Replace the 
fuser unit. 
If any attempt 
of using new 
fuser unit as 
a trial is going 
to be made, 
be sure to use 
the System 
Maintenance 
Menu FUSE 
KEEP MODE.

 Installation position 
of the lower 
thermistor

The lower thermister must be installed while 
contacting with the fuser unit. Check if the lower 
thermister is installed in the far position from the 
specified position or not causing detection of the 
lower temperature than the actual temperature 
of fuser unit.

 Replace the 
fuser unit. 
If any attempt 
of using new 
fuser unit as 
a trial is going 
to be made, 
be sure to use 
the System 
Maintenance 
Menu FUSE 
KEEP MODE.

(11-2-3) AC power input to the halogen lamp

 AC power voltage 
from the low voltage 
power supply

 Check if the AC voltage for heater is normally 
supplied or not. 
Power supply CN2 connector 

, between pin-1 

and pin-2, and between pin-3 and pin-4.

 Replace the low 
voltage power 
supply.

Heater ON signal 
that is output 
from PU to the 
low voltage power 
supply

Check that the heater ON signal goes active at 
the warming up timing, or not. 
"L" active while ON. 
Power connector 

 of the PU board, between 

pin-11 and pin-12.

Replace the PU 
board.

7.5.2.(12)  Motor fan error  (error code 122, 127, 128, 918, 051)

(12-1)  The low voltage power supply fan does not rotate immediately after the power is 

turned on.

Check item

Check work

Action to be taken 

at NG

(12-1-1) Cable connection condition and wiring condition

Cable connection 
condition and wiring 
condition of the 
low voltage power 
supply fan and 
those of the fuser 
fan

Check if the connectors are connected normally 
or not. 
Check if extra length of the cables does not 
touch the fan blade or not.

Correct the 
connection 
condition of 
the connectors. 
Correct the 
cable wiring 
route. Replace 
the fan.

(12-2)  Duplex fan does not rotate during the Duplex printing.

Check item

Check work

Action to be taken 

at NG

(12-1-2) Cable connection condition and wiring condition

Cable connection 
condition and wiring 
condition of the 
Duplex fan

Check if the connectors are connected normally 
or not. 
Check if extra length of the cables does not 
touch the fan blade or not.

 Correct the 
connection 
condition of 
the connectors. 
Correct the 
cable wiring 
route. Replace 
the fan. 
Replace the fan.

24v fuse F501 of 
the Duplex board 
(v7y PCB)

Check if the fuse F501 has blown out or not.

Replace the 
Duplex board 
(v7y PCB).

24v power supplied 
to the Duplex board 
(v7y PCB).

Check if the fuse F1 of the PU board has blown 
out or not.

Replace the PU 
board.

Содержание C810






























































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды