Oki C810 Скачать руководство пользователя страница 48

Страница: 48 / 253

44015503TH Rev. 1

47 /

Oki Data CONFIDENTIAL

3. INSTALLATION

3. Place the printer on the stack of additional trays.

Personal injury may occur.

Since the printer weights approximately 40 kg, it should be lifted by two or more

people.

Proceed to step 5 when one additional tray is used.

Printer

Added tray

Cabinet

Hole on the
bottom

4. Install the support plate.

Memo The plate can be installed only when two additional trays are used. It cannot

be installed for the printer main unit only when one additional tray is used.

Open the multi-purpose tray.

Multi-purpose
tray

Front cover

Align the holes on the bottom of the

printer to the pins of the additional tray.

Place the printer gently on the stack of

additional trays.

Push up the center handle (blue) to

open the front cover.

Push the OPEN button to open the top

cover.

Top cover

OPEN button

Содержание C810






























































































































































































































































Результаты поиска

Содержание C810

Отзывы:

Бренды по названию

Популярные бренды

Oki C810, Руководство по обслуживанию

Результаты поиска

Содержание C810

Отзывы:

Бренды по названию

Популярные бренды