Oki C810 Скачать руководство пользователя страница 40

Страница: 40 / 253

44015503TH Rev. 1

39 /

Oki Data CONFIDENTIAL

3. INSTALLATION

Place the print side down.

Paper size dial

Paper guide

Paper loading orientation

A4, B5, Letter

Loading paper in the paper cassette

(1) Pull out the paper cassette.

Note! Do not remove the rubber from the plate.

(2) Adjust the paper stopper and paper guide to the size of the paper being used.

Note! When setting A6 size paper, move the paper stopper toward you to remove it.

Then attach it to the position shown.

(3) Fan the edges of paper stack and align the edges of the stack on a level surface.

(4) Load the paper with the print side facing down.

Note! • Place the paper against the front side of the paper cassette.

• Do not allow the level of paper to pass the “

” mark of the paper guide (300

sheets of 70 kg paper).

(5) Hold the paper with the paper guide.

(6) Turn the paper size dial to the size of the paper you load.

(7) Return the paper cassette to the printer.

Plate

Paper guide

Paper stopper

Содержание C810






























































































































































































































































Результаты поиска

Содержание C810

Отзывы:

Бренды по названию

Популярные бренды

Oki C810, Руководство по обслуживанию

Результаты поиска

Содержание C810

Отзывы:

Бренды по названию

Популярные бренды