manualshive.com logo in svg

Oki C810, Руководство по обслуживанию

Поделиться
Скачать
Oki C810 Скачать руководство пользователя страница 162

44015503TH  Rev. 1 

161 /

Oki  Data  CONFIDENTIAL

7.  TROUBLESHOOTING PROCEDURE

Panel display

(The mark indicates no 

message in the upper row.)

ON

LINE
lamp

Inspec-

tion

lamp

Details

Remedial

measure

Deleting data

Blink varies Cancel of the job is indicated. A 

printer is discarding the data until end 
of the job.

—

Deleting data

Blink varies This message is displayed when a 

jam occurs during jam recovery off.
Cancel of the job is indicated. A 
printer is discarding the data until end 
of the job.

—

Deleting data

Blink varies Indicates that canceling of a printing 

without permission is in progress. (Job 
Account related)
1. When a job is received from a user 

that is not authorized to print.

2. When a color job is received from a 

user that is not authorized to make 
a color print.

—

Deleting data

Blink varies Indicates that canceling a job is in 

progress because the log storage area 
inside a printer has run out of memory 
space, and the operation "Cancel the 
job" is specified at log full.
(JobAccount)

—

 

Printer is preparing.

varies varies Indicates checking of Toner cartridge 

is in progress.

—

 

Adjusting the fuse 
temperature.

varies varies Indicates that a printer is in the midst 

of cooling down. Note that (period) 
is added at the end of message 
“Adjusting the fuse temperature”.

—

 

Adjusting the fuse 
temperature

varies varies Indicates that the printer is in the 

midst of warming up.

—

 

Adjusting 
temperature

varies varies Indicates that printing is stopped 

temporarily due to high temperature 
of a drum. Alternately, this message 
indicates that a printer is in the 
standby state waiting for the thermal 
cooling down when switching paper 
size from narrow to wide.

—

Panel display

(The mark indicates no 

message in the upper row.)

ON

LINE
lamp

Inspec-

tion

lamp

Details

Remedial

measure

 

In the power save 
mode

varies varies Indicates that a printer is in the power 

save status.
When a printer enters the power save 
mode, the LCD backlight turns off.
When it exits the power save mode, 
the LCD backlight turns on. If the 
switch is pressed while the backlight 
is off (in the power save mode), the 
backlight turns on, and then turns off 
in 30 seconds.
However, the power save mode is 
not canceled. The backlight turns on 
during shut-down (Priority 365).

—

Adjusting color

varies varies Indicates that the automatic color 

registration correction is in progress.

—

 

Adjusting density

varies varies Indicates that the automatic density 

correction is in progress. The status 
code 10988 corresponds to the 
density read-out (Leisus – STSDEN 
#1) and 10994 corresponds to the 
density correction (Leisus – STSDEN 
#0).

—

Flash Download

varies varies Indicates that downloading of the PU 

firmware program data is in progress.
Since downloading of the PU 
firmware is opened internally only 
and not disclosed to user, the status 
will not occur in the user environment.

—

 

Security kit is 
installed. 

varies varies Indicates that security kit is being 

applied. After the security kit has 
been applied, it is generally on 
displaying while the printer is standby.

—

Содержание C810






























































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды