Oki C810 Скачать руководство пользователя страница 182 | Manualshive

Страница: 182 / 253

Oki C810 Скачать руководство пользователя страница 182

44015503TH Rev. 1

181 /

Oki Data CONFIDENTIAL

7. TROUBLESHOOTING PROCEDURE

Check item

Check work

Action to be taken

at NG

(1-1-5) LSI operation check

I/F signal supplied
from the PU board
to the Operator
Panel board.

Check if the signal is output to the OPE
connector

of the PU board or not.

Pin-7: Send data (Sending data from the PU
board)
Pin-9: CLR

If it is normal, the signal is output always.

Replace the PU
board.

I/F signal supplied
from the PU board
to the Operator
Panel board.

Check if the signal is output to the OPE
connector

of the PU board or not.

Pin-6: Send data (Sending data from the PU
board)

If it is normal, the signal is output always.

Replace the
Operator Panel
board.

Note) However, for the Data Protection Kit –A3, refer to section 7.8.

(1-2) PLEASE WAIT

(If the message is left attended, the error number changes to “COMMUNICATION

ERROR”.)

Check item

Check work

Action to be taken

at NG

(1-2-1) Check installation condition of printed circuit board

Connection
condition of the PU
board and CU board

Check the connection condition of the CU IF
connector

of the PU board, and check that of

the FFC connector of the CU board.

Connect the
FFC normally.

(1-2-3) Implement version upgrade of the PU firmware

version upgrade of
the PU firmware

When the PU firmware version upgrade is
completed, this display appears.
Check the PU firmware version number by using
the menu print or the maintenance function.

If the message
reappears after
the power is re-
started again,
implement the
confirmations of
sections (1-3-1)
and (1-3-2).

(1-3) Error messages related to Operator Panel are displayed.

Check item

Check work

Action to be taken

at NG

(1-3-1) Error message

Error message

Check the error contents by referring to the Error
Message List.

Follow the
instruction.

(1-4) Displaying as “RAM check” or “Initializing”.

Check item

Check work

Action to be taken

at NG

(1-4-1) Operator Panel display freezes.

Operator Panel
display

Keep displaying “RAM Check" or "Initializing".

Replace the
ROM DIMM of
CU, or replace
the CU board.
Remove the
optional RAM
and HDD. Then
perform the
check.
If the check
result shows
NG, replace the
CU board.
Note!

«
...
180
181
182
183
184
...
»

Содержание C810






























































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды