Oki C810 Скачать руководство пользователя страница 28

Страница: 28 / 253

44015503TH Rev. 1

27 /

Oki Data CONFIDENTIAL

2. DESCRIPTION OF OPERATION

outline of density correction

The density is corrected by reading the correction pattern that is printed on the belt with the

density sensor located inside the sensor shutter under the belt unit.

Automatic start timing of density correction:

• At power-on

• When the ID count after the previous correction exceeds 500

A correction error may be issued due to an inadequate toner amount of the pattern

generated, a sensor stained with toner, deficient opening/closing of the shutter, or for other

reasons.

However, even if an error is issued, it is not indicated on the operator panel. Therefore,

forcible density correction will have to be performed in the self-diagnostic mode (section

5.3.2.7) to check the error indication.

Density correction pattern

Density sensor

Transport belt

Sensor shutter

Belt waste toner box

Belt cleaning blade

Density sensor

Содержание C810






























































































































































































































































Результаты поиска

Содержание C810

Отзывы:

Бренды по названию

Популярные бренды

Oki C810, Руководство по обслуживанию

Результаты поиска

Содержание C810

Отзывы:

Бренды по названию

Популярные бренды